Skip to content

Getting around in 3D

The same controls work on the site and on a floor. Click the i button in the top corner of the 3D view (or press I) at any time to see them.

Buttons in the corner

Button What it does
Start tour (play) Starts the camera tour — see Tour below. While it plays, the same button stops it
Demo view Engineers only: shows the machines as running, or in a mix of states — see Demo view below
Reset view Shows the whole site or floor again
Top view Looks straight down, with north at the top on the site
Zoom in / Zoom out Moves closer or further away
Turn left / Turn right Turns the view around its middle
i Lists every control and shortcut

On the site, the compass under the buttons always points north.

Mouse

Action What it does
Left-drag Rotate around
Right-drag, or Ctrl + left-drag Move
Scroll wheel Zoom towards the pointer
Click Select
Double-click On the site: go inside a building or area. On a floor: go to the machine
Double-click the ground Go to that spot

Touchpad

Laptop touchpads work without a mouse:

Gesture What it does
Two-finger swipe Move, like sliding a map
Pinch Zoom towards the pointer
Shift + two-finger swipe Rotate around and tilt
Press and drag Rotate around

Keyboard

The keyboard works while the pointer is over the 3D view, or after you click it. It never interferes with typing in a field.

Keys What they do
W A S D or the arrow keys Move
Q / E, or Shift + ← / → Turn left / right
Shift + ↑ / ↓ Tilt
+ / − Zoom in / out
0 or Home Reset view
T Top view
F Go to the selected machine
I Show or hide the controls
Esc Stop the tour

Hold a key to keep moving; movement is faster when you're zoomed out.

If scrolling does the wrong thing

Scrolling over the 3D view zooms with a mouse wheel and moves with a touchpad swipe. Enture tells the two apart automatically. Some mice with smooth scrolling look like a touchpad — if scrolling moves the view when you wanted to zoom (or the other way round), open the i panel and under Scroll wheel / two-finger swipe choose Zoom or Move instead of Automatic. Your browser remembers the choice.

Scrolling over the 3D view never scrolls the page; scroll the page from anywhere outside the 3D view.

Tour

The tour flies the camera through the site or the floor you are looking at, so you can watch everything without moving the view yourself. Anyone can use it.

Click Start tour (the play button at the top of the corner buttons). The camera starts on the whole view, then:

  • On the site: it circles each building (its label shows how many of its machines are running, idle, in alarm and so on), then visits each outdoor area and the equipment in it, then the equipment standing on open ground.
  • On a floor: it goes zone by zone — each line, cell or area — passing slowly along its machines, then visits the machines that are not in a zone.

It always moves on to the nearest next stop, so it never zig-zags across the site. Every machine gets the same time. The card in the bottom corner names the machine being shown, with its live status. Then the camera rises back to the whole view and the tour starts again, until you stop it.

To stop the tour, click the button again, press Esc, or move the camera any way you like (drag, scroll, a camera key or a corner button). The tour is not available while you are editing.

Tour length: open the i panel and under Tour choose Short, Normal or Long. Longer tours come closer to each machine and stay longer. Your browser remembers the choice.

If your device is set to reduce motion, the tour does not fly: it shows one item at a time, fading from one to the next.

Screen mode

Screen mode is for showing the twin on a wall screen or a TV in the plant.

  1. Open the i panel and click Open screen mode. It opens in a new browser tab. You can also bookmark that tab's address, or open it on the screen's computer.
  2. The 3D view fills the browser window, with no menus. Move the mouse to show the Full screen and Exit screen mode buttons; they hide again after a few seconds. Click Full screen once to fill the whole screen.
  3. The tour starts by itself. It tours the site, then each floor in turn (building by building, from the lowest floor up; empty floors are skipped), then the site again, and carries on forever.

  4. Live statuses keep updating while it plays, and the layout reloads by itself every few minutes, so changes made by engineers appear without a refresh.

  5. If someone moves the camera, the tour pauses, and it carries on by itself after 30 seconds with nobody touching it.
  6. The screen is kept from going to sleep while screen mode is open (on browsers that allow it).
  7. Click Exit screen mode to go back to the normal page.

The screen's browser must stay signed in to Enture. A tour keeps the 3D view drawing all the time, so it uses more power than a still view.

Demo view

Engineering access required

The Demo view button shows only with engineering access and Engineering Mode switched on.

The demo view shows how the site looks with its machines working — useful while you build the layout, before anything is linked to real machines, and for showing the site to someone.

  1. Click Demo view in the corner of the 3D view.
  2. Pick what to show:
    • All running — every piece of equipment running: the green light on, moving parts going.
    • Mixed — mostly running, with some idling and a few in alarm, so you can see every state.
    • Live — back to the real statuses.

While the demo view is on:

  • A banner across the top of the 3D view says Demo view — not live data.
  • Equipment that is not linked to a machine yet shows a light too.
  • Building and area labels hide their status counts, and the tour card says Demo instead of a status.
  • Everything outside the 3D view — the lists, the machine details, alarms and notifications — still shows the real data. Nothing is saved or sent.

The demo view works in the editor and with the tour. It switches back to live when you leave the page or switch Engineering Mode off, and it is never part of a shared link or screen mode.